Features
- Rotate faster & slower (315 rpms – 5 rpms) than any other rotary evaporator on the market, so you can test new SOPs and develop better methods.
- Easily manage your expensive samples with small flask sizes (from 100ml to 2L).
- Program rotation direction changes, ramps, and other automations to get more done in the lab at once.
- Eliminate most manual steps in the sample drying and removal process by creating finer dry granules (ask us how).
- Easily analyze the residue left over after distillation.
- Orient for left or right-handed operation based on your limited bench space.
- Get a purpose-built R&D mini rotary evaporator priced 10-20% better than comparable models from the other names you know.
Want to know more? Complete the form above, tell us a little about your application, and we’ll work with you to find the best solution.
Why choose a mini rotary evaporator for R&D?
f you’re in process development, method development, or doing basic R&D, most rotovaps on the market aren’t actually built for you.
If your job is testing new recipes, why use an instrument that’s built to follow a recipe?
Yamato mini rotary evaporators are built specifically for process development, with a wider range of rotation speeds than any other rotovap on the market (at 5 to 315 rpms).
That’s about 15% more range than any other rotary evaporator.
And a more appropriate flask size for your work, from a max of a 2L rotary evaporator flask down to 100ml.
Plus, you can program your test methods or SOPs into the system and walk away.
- Spin forward at 15 rpms for 20 seconds
- Spin backward at 15 rpms for 20 seconds
- Repeat for 60 minutes
It’s the only one that lets you work out the best method for your new process without limitations.
Plus, depending on your model, these are priced 10-20% better than comparable models from the other names you know.
Specifications
| Performance*¹ | Operating ambient temp. range | 5~35°C | |||
| Speed range | 5~315 rpm*³ | ||||
| Evaporation capacity | Up to 23 ml/min (water) | ||||
| Functions | RPM display | Digital display / Encoder dial setting | |||
| Rotation mode | Forward/Reverse/Auto reverse | ||||
| Spring-loaded jack | Manual balance (Max. height 200 mm, stepless regulation, one-touch lock) | ||||
| Configuration | Vacuum controller | --- | |||
| Vacuum control solenoid valve | --- | ||||
| Rotary motor | DC brushless (simple servo) | ||||
| Condenser retention | Condenser bracket | ||||
| Safety functions | Rotary evaporator | DC motor: Motor overload protection, overvoltage, low voltage, rotation speed sensor error AC adapter: Short circuit in internal circuit, overcurrent protection, overvoltage protection |
|||
| Vacuum controller | --- | ||||
| Standard | Cooling condenser | Double corrugated tube (cooling surface: 0.143 m²) |
|||
| Suction Port: GL-14 (upper), Φ10 nozzle |
|||||
| Cooling port: GL14 (two places in lower part), two φ10 nozzles | |||||
| Compatible evaporation flask | 0-2000ml for TS24. Use optional reducer to attach small flasks. | ||||
| Compatible receiving flask | 100-2000 ml | ||||
| External dimensions*² (W x D x H) | 529 × 324 × 745 | ||||
| Overall dimensions*² (W x D x H) | 554 × 365 × 745 | ||||
| Power rating 50/60Hz |
RE202 and REV202M: 100-115V 1A with plug RE212 and REV212M: 200-230V single phase 1A no plug, round terminal |
||||
| Weight | ~10.0 kg (main unit only) | ||||
| Included accessories | Main unit | AC adapter (1), power cable (1), bath guide (1), rear cover (1), single-sided tape fastener roll (1), double-sided tape fastener roll (1) |
|||
| Glass set | Cooling condenser (type A/B)(1), rotary joint (1), evaporation flask (1), receiving flask (1), ball joint clamp (1), flask clip (1), vacuum seal (1), condenser insulation kit (1), condenser bracket (1) (for type B), hex wrench (1) (for type B) |
||||
